I did it and now its buttery smooth loading shells. Is the bolt fully in battery? With the prep work in place, I started carving with the Tungsten Carbide Cutter at medium speed.

Using the 240grit sanding disc for a rough polish. Carving with the Tungsten bit at medium speed. Verify Human or Spambot ? Once the basic shape was in place, I moved on to the sanding drum to knock down any “hills” I might have created. You can always take more material away, but it’s impossible to add it back once you’ve gone too far. Using 120 grit Drum to knock down high spots. The drum probably isn’t the most ideal bit for “carving” the aluminum receiver, as it is a 120 grit sanding band coated with aluminum oxide. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. I'll look into polishing the carrier latch. Feathering pressure at the beginning and end of each pass. You might repeat this same process three or four times until you get your loading port just right.

Still, the larger diameter 1/2″ drum was helpful in smoothing things out and put on a pre-finish. Benelli’s M2 semiautomatic shotgun is legendary for rugged reliability you can count on in the most adverse of circumstances and conditions. Been running a 870 for years and finally upgraded to a new Benelli M2. Powered by Invision Community, New Benelli M2 is extremely difficult to load, This Forum is full of em...(truly nice people).

Obviously, this makes it useless as a competition gun. If you know someone else with an M2 have them stuff a few shells into the gun and see if it is more difficult to load than the one they have... i think its broke, I'll give you 400.00 for it as is!!!!! mostly parallel) to the path that I’d expect a pair of shells to take when using the load four method. You might repeat this same process three or four times until you get … The bolt and inertia spring are in effect free-floating and initially remain where they are. Been running a 870 for years and finally upgraded to a new Benelli M2. Does it get easier with use, or is something messed up? Since I’ve only removed minimal material from the receiver to this point, I don’t want to spend too much time putting a polished finish on. A little searching I found this out of the UK. Opening the loading port on a Benelli M2 (DIY), on Opening the loading port on a Benelli M2 (DIY), Principles of Choosing a Shot Shell Caddy, Introducing the Enhanced Trigger Guard from A&S Engineering, What to Look for When Shopping for a 3-Gun Shotgun, Benelli M2 (substitute for just about any other shotgun, though), Masking Tape & Cloth to cover inside of receiver, Dremel Flex shaft adapter (optional, but it seriously helps). You need to polish the carrier latch - do a search and there is lots of advice on here of how to do it. I own four O/Us and one awesome Benelli M1. Nice shotgun, but its extremely difficult to load rounds into the magazine. The M2 Field shotgun is light, durable, fast-handling and the backbone of the Benelli semi-auto line. Aside from adding a magazine extension tube, opening the loading port up on your shotgun is probably the most important modification you make.

When the shot is fired all the fixed parts of the gun go rearward with the recoil. It is important not to affect the legibility of the serial number, and avoid carving out any material beyond the edge of the trigger housing. There are plenty of shops out there that will do this for a nominal fee, but probably the most influential factor in making this modification myself was that it’d be tailored to my exact need and loading style, versus spending money for an end result that still might need to be tweaked. Benelli M2 (substitute for just about any other shotgun, though) Bench Vise; Masking Tape & Cloth to cover inside of receiver; Dremel; Dremel Flex shaft adapter (optional, but it seriously helps) 9903 Tungsten Carbide Cutter; 407 1/2″ Sanding Drum; 413 Sanding Discs, 240 grit . The M2 uses Benelli’s famous rotating locking bolt action. go to : http://forums.pigeon...elli-m2-tweaks/. The force from the mag spring isn't the issue--it's getting the rim of each round over the cartridge retaining lever.

My first step was to disassemble the shotgun and use the masking tape to mark off how much material I wanted to remove. This was a DIY task that warranted much contemplation when I considered the risk of potentially ruining a $1,400 shotgun, but some practice with a less expensive 870 made me a bit more comfortable with the process. Constant, firm pressure in a uniform motion will take material away at a comfortable rate. First rough pass completed, time to test and make enhancements as needed. March 15, 2010 in Shotgun - Technical. Nice shotgun, but it's extremely difficult to load rounds into the magazine. Mine was doing the same thing, right about when the rim hit it would get really tight and then you could push past it. topgunpilot20, The bolt is fully in battery. Captcha: An avid 3gunner here to gain and share my experiences in a rapidly growing sport. Moving up to full speed, carving got much easier. Again, a uniform motion while applying firm pressure was key. Aren't all shotguns extremely difficult to reload? It cycles everything from target loads to the heaviest 3-inch magnums, and has earned a reputation for excellence in fields, blinds and at shooting ranges around … The overall idea is to be able to easily engage the shell catch with each load, and avoiding an accidental ghost load that will cost many seconds in a stage. I was hoping to use this gun at the Larue 3 Gun coming up. BrianEnos.com Before beginning, remember to take things slow.

The force from the mag spring isnt the issue--its getting the rim of each round over the cartridge retaining lever. Or is that just me? All of our competition ready M2's have the following features: Benelli M2 Competition Ready Shotgun: $2,300, Conversion on customer supplied gun: $1,300, Get the latest updates on new products and upcoming sales, CUSTOMER SUPPLIED GUN - Benelli M2 Competition Ready Shotgun, Loading port opened and polished, optimized for twin and quad loading methods, Extended and polished stainless steel shell carrier (lifter), Shell latch tuned and polished for reduced resistance when loading, Lightened and polished bolt body (standard bolt body available as well), Bold modified for out-of-battery and 'ghost' loading, Nordic Components magazine tube, 12 round capacity (other tube lengths available), Tested for slug accuracy and re-zeroed if needed. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. By Before beginning, remember to take things slow. Also, it's extremely difficult and sometime impossible to manually unload the magazine by pressing on the cartridge retaining lever. The effort required should be minimal to get the shell in. there are lots and lots of advice on how to make Benelli's more user friendly, just do a search. Working corners parallel to the path that shells will take when using load four method. Caution had to be taken not to dig in too deep and create hills & valleys in the edge.

Try a different, smaller plug, that seemed to help my M2. With this first run complete, it’s time to get the lifter welded up and see what additional modifications I need to make, if any. I am the first to admit, I do not know crap about shotguns but I know Taran Butler and he recommends Salient!

I did it and now its buttery smooth loading shells. Is the bolt fully in battery? With the prep work in place, I started carving with the Tungsten Carbide Cutter at medium speed.

Using the 240grit sanding disc for a rough polish. Carving with the Tungsten bit at medium speed. Verify Human or Spambot ? Once the basic shape was in place, I moved on to the sanding drum to knock down any “hills” I might have created. You can always take more material away, but it’s impossible to add it back once you’ve gone too far. Using 120 grit Drum to knock down high spots. The drum probably isn’t the most ideal bit for “carving” the aluminum receiver, as it is a 120 grit sanding band coated with aluminum oxide. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. I'll look into polishing the carrier latch. Feathering pressure at the beginning and end of each pass. You might repeat this same process three or four times until you get your loading port just right.

Still, the larger diameter 1/2″ drum was helpful in smoothing things out and put on a pre-finish. Benelli’s M2 semiautomatic shotgun is legendary for rugged reliability you can count on in the most adverse of circumstances and conditions. Been running a 870 for years and finally upgraded to a new Benelli M2. Powered by Invision Community, New Benelli M2 is extremely difficult to load, This Forum is full of em...(truly nice people).

Obviously, this makes it useless as a competition gun. If you know someone else with an M2 have them stuff a few shells into the gun and see if it is more difficult to load than the one they have... i think its broke, I'll give you 400.00 for it as is!!!!! mostly parallel) to the path that I’d expect a pair of shells to take when using the load four method. You might repeat this same process three or four times until you get … The bolt and inertia spring are in effect free-floating and initially remain where they are. Been running a 870 for years and finally upgraded to a new Benelli M2. Does it get easier with use, or is something messed up? Since I’ve only removed minimal material from the receiver to this point, I don’t want to spend too much time putting a polished finish on. A little searching I found this out of the UK. Opening the loading port on a Benelli M2 (DIY), on Opening the loading port on a Benelli M2 (DIY), Principles of Choosing a Shot Shell Caddy, Introducing the Enhanced Trigger Guard from A&S Engineering, What to Look for When Shopping for a 3-Gun Shotgun, Benelli M2 (substitute for just about any other shotgun, though), Masking Tape & Cloth to cover inside of receiver, Dremel Flex shaft adapter (optional, but it seriously helps). You need to polish the carrier latch - do a search and there is lots of advice on here of how to do it. I own four O/Us and one awesome Benelli M1. Nice shotgun, but its extremely difficult to load rounds into the magazine. The M2 Field shotgun is light, durable, fast-handling and the backbone of the Benelli semi-auto line. Aside from adding a magazine extension tube, opening the loading port up on your shotgun is probably the most important modification you make.

When the shot is fired all the fixed parts of the gun go rearward with the recoil. It is important not to affect the legibility of the serial number, and avoid carving out any material beyond the edge of the trigger housing. There are plenty of shops out there that will do this for a nominal fee, but probably the most influential factor in making this modification myself was that it’d be tailored to my exact need and loading style, versus spending money for an end result that still might need to be tweaked. Benelli M2 (substitute for just about any other shotgun, though) Bench Vise; Masking Tape & Cloth to cover inside of receiver; Dremel; Dremel Flex shaft adapter (optional, but it seriously helps) 9903 Tungsten Carbide Cutter; 407 1/2″ Sanding Drum; 413 Sanding Discs, 240 grit . The M2 uses Benelli’s famous rotating locking bolt action. go to : http://forums.pigeon...elli-m2-tweaks/. The force from the mag spring isn't the issue--it's getting the rim of each round over the cartridge retaining lever.

My first step was to disassemble the shotgun and use the masking tape to mark off how much material I wanted to remove. This was a DIY task that warranted much contemplation when I considered the risk of potentially ruining a $1,400 shotgun, but some practice with a less expensive 870 made me a bit more comfortable with the process. Constant, firm pressure in a uniform motion will take material away at a comfortable rate. First rough pass completed, time to test and make enhancements as needed. March 15, 2010 in Shotgun - Technical. Nice shotgun, but it's extremely difficult to load rounds into the magazine. Mine was doing the same thing, right about when the rim hit it would get really tight and then you could push past it. topgunpilot20, The bolt is fully in battery. Captcha: An avid 3gunner here to gain and share my experiences in a rapidly growing sport. Moving up to full speed, carving got much easier. Again, a uniform motion while applying firm pressure was key. Aren't all shotguns extremely difficult to reload? It cycles everything from target loads to the heaviest 3-inch magnums, and has earned a reputation for excellence in fields, blinds and at shooting ranges around … The overall idea is to be able to easily engage the shell catch with each load, and avoiding an accidental ghost load that will cost many seconds in a stage. I was hoping to use this gun at the Larue 3 Gun coming up. BrianEnos.com Before beginning, remember to take things slow.

The force from the mag spring isnt the issue--its getting the rim of each round over the cartridge retaining lever. Or is that just me? All of our competition ready M2's have the following features: Benelli M2 Competition Ready Shotgun: $2,300, Conversion on customer supplied gun: $1,300, Get the latest updates on new products and upcoming sales, CUSTOMER SUPPLIED GUN - Benelli M2 Competition Ready Shotgun, Loading port opened and polished, optimized for twin and quad loading methods, Extended and polished stainless steel shell carrier (lifter), Shell latch tuned and polished for reduced resistance when loading, Lightened and polished bolt body (standard bolt body available as well), Bold modified for out-of-battery and 'ghost' loading, Nordic Components magazine tube, 12 round capacity (other tube lengths available), Tested for slug accuracy and re-zeroed if needed. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. By Before beginning, remember to take things slow. Also, it's extremely difficult and sometime impossible to manually unload the magazine by pressing on the cartridge retaining lever. The effort required should be minimal to get the shell in. there are lots and lots of advice on how to make Benelli's more user friendly, just do a search. Working corners parallel to the path that shells will take when using load four method. Caution had to be taken not to dig in too deep and create hills & valleys in the edge.

Try a different, smaller plug, that seemed to help my M2. With this first run complete, it’s time to get the lifter welded up and see what additional modifications I need to make, if any. I am the first to admit, I do not know crap about shotguns but I know Taran Butler and he recommends Salient!

I did it and now its buttery smooth loading shells. Is the bolt fully in battery? With the prep work in place, I started carving with the Tungsten Carbide Cutter at medium speed.

Using the 240grit sanding disc for a rough polish. Carving with the Tungsten bit at medium speed. Verify Human or Spambot ? Once the basic shape was in place, I moved on to the sanding drum to knock down any “hills” I might have created. You can always take more material away, but it’s impossible to add it back once you’ve gone too far. Using 120 grit Drum to knock down high spots. The drum probably isn’t the most ideal bit for “carving” the aluminum receiver, as it is a 120 grit sanding band coated with aluminum oxide. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. I'll look into polishing the carrier latch. Feathering pressure at the beginning and end of each pass. You might repeat this same process three or four times until you get your loading port just right.

Still, the larger diameter 1/2″ drum was helpful in smoothing things out and put on a pre-finish. Benelli’s M2 semiautomatic shotgun is legendary for rugged reliability you can count on in the most adverse of circumstances and conditions. Been running a 870 for years and finally upgraded to a new Benelli M2. Powered by Invision Community, New Benelli M2 is extremely difficult to load, This Forum is full of em...(truly nice people).

Obviously, this makes it useless as a competition gun. If you know someone else with an M2 have them stuff a few shells into the gun and see if it is more difficult to load than the one they have... i think its broke, I'll give you 400.00 for it as is!!!!! mostly parallel) to the path that I’d expect a pair of shells to take when using the load four method. You might repeat this same process three or four times until you get … The bolt and inertia spring are in effect free-floating and initially remain where they are. Been running a 870 for years and finally upgraded to a new Benelli M2. Does it get easier with use, or is something messed up? Since I’ve only removed minimal material from the receiver to this point, I don’t want to spend too much time putting a polished finish on. A little searching I found this out of the UK. Opening the loading port on a Benelli M2 (DIY), on Opening the loading port on a Benelli M2 (DIY), Principles of Choosing a Shot Shell Caddy, Introducing the Enhanced Trigger Guard from A&S Engineering, What to Look for When Shopping for a 3-Gun Shotgun, Benelli M2 (substitute for just about any other shotgun, though), Masking Tape & Cloth to cover inside of receiver, Dremel Flex shaft adapter (optional, but it seriously helps). You need to polish the carrier latch - do a search and there is lots of advice on here of how to do it. I own four O/Us and one awesome Benelli M1. Nice shotgun, but its extremely difficult to load rounds into the magazine. The M2 Field shotgun is light, durable, fast-handling and the backbone of the Benelli semi-auto line. Aside from adding a magazine extension tube, opening the loading port up on your shotgun is probably the most important modification you make.

When the shot is fired all the fixed parts of the gun go rearward with the recoil. It is important not to affect the legibility of the serial number, and avoid carving out any material beyond the edge of the trigger housing. There are plenty of shops out there that will do this for a nominal fee, but probably the most influential factor in making this modification myself was that it’d be tailored to my exact need and loading style, versus spending money for an end result that still might need to be tweaked. Benelli M2 (substitute for just about any other shotgun, though) Bench Vise; Masking Tape & Cloth to cover inside of receiver; Dremel; Dremel Flex shaft adapter (optional, but it seriously helps) 9903 Tungsten Carbide Cutter; 407 1/2″ Sanding Drum; 413 Sanding Discs, 240 grit . The M2 uses Benelli’s famous rotating locking bolt action. go to : http://forums.pigeon...elli-m2-tweaks/. The force from the mag spring isn't the issue--it's getting the rim of each round over the cartridge retaining lever.

My first step was to disassemble the shotgun and use the masking tape to mark off how much material I wanted to remove. This was a DIY task that warranted much contemplation when I considered the risk of potentially ruining a $1,400 shotgun, but some practice with a less expensive 870 made me a bit more comfortable with the process. Constant, firm pressure in a uniform motion will take material away at a comfortable rate. First rough pass completed, time to test and make enhancements as needed. March 15, 2010 in Shotgun - Technical. Nice shotgun, but it's extremely difficult to load rounds into the magazine. Mine was doing the same thing, right about when the rim hit it would get really tight and then you could push past it. topgunpilot20, The bolt is fully in battery. Captcha: An avid 3gunner here to gain and share my experiences in a rapidly growing sport. Moving up to full speed, carving got much easier. Again, a uniform motion while applying firm pressure was key. Aren't all shotguns extremely difficult to reload? It cycles everything from target loads to the heaviest 3-inch magnums, and has earned a reputation for excellence in fields, blinds and at shooting ranges around … The overall idea is to be able to easily engage the shell catch with each load, and avoiding an accidental ghost load that will cost many seconds in a stage. I was hoping to use this gun at the Larue 3 Gun coming up. BrianEnos.com Before beginning, remember to take things slow.

The force from the mag spring isnt the issue--its getting the rim of each round over the cartridge retaining lever. Or is that just me? All of our competition ready M2's have the following features: Benelli M2 Competition Ready Shotgun: $2,300, Conversion on customer supplied gun: $1,300, Get the latest updates on new products and upcoming sales, CUSTOMER SUPPLIED GUN - Benelli M2 Competition Ready Shotgun, Loading port opened and polished, optimized for twin and quad loading methods, Extended and polished stainless steel shell carrier (lifter), Shell latch tuned and polished for reduced resistance when loading, Lightened and polished bolt body (standard bolt body available as well), Bold modified for out-of-battery and 'ghost' loading, Nordic Components magazine tube, 12 round capacity (other tube lengths available), Tested for slug accuracy and re-zeroed if needed. The Benelli M2 is universally recognized as one of the most reliable and effective shotguns available for use in all types of action and tactical shooting sports. By Before beginning, remember to take things slow. Also, it's extremely difficult and sometime impossible to manually unload the magazine by pressing on the cartridge retaining lever. The effort required should be minimal to get the shell in. there are lots and lots of advice on how to make Benelli's more user friendly, just do a search. Working corners parallel to the path that shells will take when using load four method. Caution had to be taken not to dig in too deep and create hills & valleys in the edge.

Try a different, smaller plug, that seemed to help my M2. With this first run complete, it’s time to get the lifter welded up and see what additional modifications I need to make, if any. I am the first to admit, I do not know crap about shotguns but I know Taran Butler and he recommends Salient!

שעות פעילות: א-ה: 8:00-17:00 ו: 8:00-14:00

Menu

Menu